This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

STAINLESS STEEL Rear Wheel Axle Pin Assembly for TRAMPA Scooter

STAINLESS STEEL Rear Wheel Axle Pin Assembly for TRAMPA Scooter 8mm STAINLESS STEEL king pin for Spring trucks Special grooved T Shaped Rear Wheel Mounting axle Spacer for Scooter - 6061 T6 Aluminum CNC Machined to perfection All Terrain Board Bearings (12 x 28 x 8mm) BLACK sidewalls with Embossed Logo ABEC 5 6001 2RS Axle Kingpin mounting bushings for TRAMPA Scooter M8 x 1.5mm Form B Kingpin Washer Marine Grade Stainless steel 10mm Rubber O-Ring to fit in Bearings - 2mm Section x 10mm Bore NITRILE 70 Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm M6 Form B Washer Marine grade Stainless steel M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck
RRP
£25
inc tax

All Terrain Board Bearings (12 x 28 x 8mm) BLACK sidewalls with Embossed Logo ABEC 5 6001 2RS

TRAMPA's very own Mountainboard Bearings measure 12 x 28 x 8mm & will fit in to all of the Hubs that TRAMPA has to offer. 

TRAMPA's precision made Bearings are polished to an internationally recognised ABEC 7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth, super fast ride with extendend free rolling & top end roll speeds.

The Bearings are designed to fit TRAMPA wheels directly to 12mm axles, however using Bearing Reducer Spacers you are able to make 6001-2RS Bearings fit to Mini Spring Truck or 12FIFTIES Truck which both use 9.525mm Axles... Using Bearing reducer sleeves on 9.525mm Axles gives a very neat flush finish to the assembly insuring your Bearings spin freely.

Mountainboard Bearings are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Removable Sides. During production the rubber coated sidewalls are inserted into the Outer raceway & are in contact with the inner raceway, they protect the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing, maintaining maximum performance to the board & rider for as long as possible. The rubber coated sidewalls come in RED, BLUE & BLACK or CERAMIC GREEN & are embossed with the TRAMPA logo proving the Top Quality!

The sidewalls are removable so you can service your bearings... Servicing your bearings on a regular basis will ensure they run well for you. Remove your wheels & take out your bearings, then using a pointy object simply pick off one side of the bearings & pop them into some solvent or fuel to dissolve any grease, i use an old tooth brush to rub the bearings gently, hopefully removing all the dirt that gets in... I pop them into another pot of clean fuel & make sure the fuel stays clean so i know the bearings are clean.. Once clean i take them out, placing onto some tissue or similar to dry out, you can rub them or blow them dry with an air line which is fun as they mae a whizzy noise! once dry i add a few tiny drops of sewing machine oil & place the bearing, open side into the wheel leaving the 1 side that still has the rubber sidewall in the outer position protecting your bearings from the further ingress of dirt getting in.... Repeat according to your riding demands, more riding = more servicing if you want best performance!

10mm Rubber O-Ring to fit in Bearings - 2mm Section x 10mm Bore NITRILE 70

This O-Ring should be fitted when a 12 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 12mm Axles.

It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

Axle Kingpin mounting bushings for TRAMPA Scooter

1mm Base Kingpin bushings for Spring Trucks. These bushings are housed within the Baseplate and Hanger. They allow the kingpin to move freely when the Truck is constructed. Made with different thickness base's to avoid any tolerance issues in production. Produced from the highest standard plastics available to ensure maximum Durabillity & to enable the best maximum performance in your Trucks. Check & replace these bushings from time to time to ensure your steering stays in top condition.    

8mm STAINLESS STEEL king pin for Spring trucks

This M8 x 80mm STAINLESS STEEL Spring Truck Kingpin is used to connect the Hanger & the Baseplate on the TRAMPA INFINITY, VERTIGO or ULTIMATE Trucks. By using an 8mm Kingpin we have managed to save loads of weight whilst retaining all the strength necessary for the job by using high quality metals true to our word!

This M8 x 80mm Kingpin connects through the truck & into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through Plastic Bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move inside each other without allowing the metal parts to touch or wear out. The Plastic Bushings will wear out over time & will eventually perish & need replacing. SO, make sure your Bushings are always in good working order after riding riding or especially when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear & tear of moving mountainboard parts.

This Kingpin lives up to TRAMPA's incredibly high quality standards, but it's always handy to have a spare just in case you do break one out on a ride.... Upgrade ur Kingpin by fitting the TRAMPA TITANIUM Kingpin which will save you loads of weight & fit into all of the TRAMPA Spring Trucks!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

In this kit you get the following items......
8mm STAINLESS STEEL king pin for Spring trucks
Custom Made T Shaped Rear Wheel Mounting Spacer made from T6 Heat Treated 6061 Aluminum that's been CNC Machined to perfection allowing your rear wheel assembly to slide into position really easily
TRAMPA ABEC 5 6001 2RS All Terrain Board Bearings - BLACK
Axle Kingpin mounting bushings for TRAMPA Scooter
M8 x 1.5mm Form B Kingpin Washer Marine Grade Stainless steel
10mm Anti Vibration Rubber O-Ring for 12mm Axles - FITS BETWEEN BEARINGS
Shim spacer - ensures exact fitting & fast running bearings
M6 Washer Form B - Marine Grade Stainless Steel
M6 Nut - Marine Grade Stainless steel Nylock nut
Weight: 80g
Please select what colour Bearings you want with your wheels?
Please select what colour Bearings you want with your wheels?
BLACK 12mm Axle 6001-2RS Mountainboard Bearing BLACK 12mm Axle 6001-2RS Mountainboard Bearing
BLUE 12mm Axle 6001-2RS Mountainboard Bearings BLUE 12mm Axle 6001-2RS Mountainboard Bearings
RED 12mm Axle 6001-2RS Mountainboard Bearings RED 12mm Axle 6001-2RS Mountainboard Bearings
CERAMIC 12mm Axle 6001-2RS Mountainboard Bearings (+£12.50) CERAMIC 12mm Axle 6001-2RS Mountainboard Bearings (+£12.50)
Quantity required:
We have enough parts to make…  
RRP £25 - per set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see UPS shipping rates you need to login.

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon