This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

25mm Marine grade Stainless Steel Countersunk Bolt Kit - fixes Mini Spring Trucks to 16ply Carve Decks

25mm Marine grade Stainless Steel Countersunk Bolt Kit - fixes Mini Spring Trucks to 16ply Carve Decks
RRP
£5
inc tax

This 25mm Marine Grade Stainless Steel Complete Deck Bolt kit fixes the Mini Spring TRUCKS to 16ply TRAMPA Carve Decks. As the amazing Vertigo baseplate has the huge weight saving hole, in order to make this hole as large as we desired we were forced to re-position the industry standard (Skate Pattern) top row fixing holes into a more suitable place & at the same time we decided to oversize this hole to give us more strength in our connection. So in order to fit the Spring Trucks to the 35º decks you need 2 sizes of bolts, M5 & M6.

All of TRAMPAs Bolts are dipped in BLUE LOCKING PASTE whilst all of the Nuts have been fitted with the world renowned "Nylock" locking system to ensure the most secure fix possible! & being made of Marine Grade Stainless Steel will never rust on you

To assemble your Board with this kit you will need
1 x 8mm Spanners
1 x 10mm Spanner

1 x 4mm Allen Key
1 x 3mm Allen Key

Firstly fix the Trucks to the deck by using the Spring Adjusters to guide you into position & mate the trucks into the deck, then push the M5 Countersunk Truck bolts through the holes closest to the crease on the top side of the Deck into & out of the truck below. Using your fingers keep the connection tight & tighten the M5 nut onto the bolt. Repeat this placing all 4 x M5 countersunk Bolts into the deck at Both ends & finger tightening their nuts on. Only finger tight for now... Then repeat with the M6 Countersunk bolts into the larger outer Bolt holes in the tip of the deck. Balance the nut on the tip of your finger & slide into position & with your other hand screw the bolt into the nut, try to make a few turns so the nut slips onto the thread ready to be tightened later... Repeat so all bolts have nuts finger tight attached.

To tighten the truck bolts use the 8mm Spanner & hold the Truck nut with the other hand, carfully tighten the 5mm Countersunk bolt with the 3mm Allen Key. Before making this bolt very tight, repeat the process using the 4mm Allen key & the 10mm spanner to tighten up the M6 nuts onto the M6 Countersunk Bolts evenly, & when everything is even go round all of the nuts and bolts & turn them all tight so you dont get any loose wobbles... 

In this kit you get :

This 2mm Marine Grade Stainless Steel Complete Deck Bolt kit fixes the Mini Spring TRUCKS to all ply 35º TRAMPA Carve Decks. As the amazing Vertigo baseplate has the huge weight saving hole, in order to make this hole as large as we desired we were forced to re-position the industry standard (Skate Pattern) top row fixing holes into a more suitable place & at the same time we decided to oversize this hole to give us more strength in our connection. So in order to fit the Spring Trucks to the 35º decks you need 2 sizes of bolts, M5 & M6.

All of TRAMPAs Bolts are dipped in BLUE LOCKING PASTE whilst all of the Nuts have been fitted with the world renowned "Nylock" locking system to ensure the most secure fix possible! & being made of Marine Grade Stainless Steel will never rust on you

To assemble your Board with this kit you will need
1 x 8mm Spanners
1 x 10mm Spanner

1 x 4mm Allen Key
1 x 3mm Allen Key

Firstly fix the Trucks to the deck by using the Spring Adjusters to guide you into position & mate the trucks into the deck, then push the M5 Countersunk Truck bolts through the holes closest to the crease on the top side of the Deck into & out of the truck below. Using your fingers keep the connection tight & tighten the M5 nut onto the bolt. Repeat this placing all 4 x M5 countersunk Bolts into the deck at Both ends & finger tightening their nuts on. Only finger tight for now... Then repeat with the M6 Countersunk bolts into the larger outer Bolt holes in the tip of the deck. Balance the nut on the tip of your finger & slide into position & with your other hand screw the bolt into the nut, try to make a few turns so the nut slips onto the thread ready to be tightened later... Repeat so all bolts have nuts finger tight attached.

To tighten the truck bolts use the 8mm Spanner & hold the Truck nut with the other hand, carfully tighten the 5mm Countersunk bolt with the 3mm Allen Key. Before making this bolt very tight, repeat the process using the 4mm Allen key & the 10mm spanner to tighten up the M6 nuts onto the M6 Countersunk Bolts evenly, & when everything is even go round all of the nuts and bolts & turn them all tight so you dont get any loose wobbles... 

In this kit you get :

In this kit you get the following items......
M5 x 25mm Countersunk Bolt - Marine Grade Stainless steel
M5 Nut - Marine Grade Stainless steel Nylock Nut
M5 Washer Form B - Marine Grade Stainless Steel
M6 x 25mm Countersunk Bolt - Marine Grade Stainless steel
M6 Nut - Marine Grade Stainless steel Nylock nut
M6 Washer Form B - Marine Grade Stainless Steel
Weight: 53g
Quantity required:
We have enough parts to make…  
RRP £5 - per set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see UPS shipping rates you need to login.

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon